Dynamix HP-51M User Manual EN-V1.00 Dynamix HPDynamix HP--51M51M HomePNA3.1 Coax MDU Master Bridge User’s GuideUser’s Guid
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 4 You can also use other Combiner or Mixer-Splitter with HP-51M to build the same system, see the
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 5 3 CCONFIGURATIONONFIGURATION This chapter describes the configuration procedure for your bridge
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 6 System Setup (TCP/IP Properties) The main window contains the left sub-window for the items to
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 7 manage other connected Slave EPs. The HCNA MAC exists only in HCNA (coax) domain, and is unaware
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 8 Each row represents for one EP, here we have one Master (Local) HCNA device (on the top) and 7
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 9 Config : configure Master’s/Smart EP’s both HomePNA and Ethernet properties or EP’s sole HomePN
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 10 HCNA driver with the new values (replace the running working values with the new setting ones)
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 11 Here we have one banned EP shown in red background after upgrade, Then power on the 2 extra
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 12 EPs are classified by the shown background color, green for allowed EP, red for banned EP. Pr
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 13 Yellow: For Master, it has inconsistent ‘Privacy Mode/Key’ settings. You may upgrade the Master
SSTATEMENTTATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may no
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 14 Service and Speed/Duplex Change ‘Service’ to enable or disable the port. This setting open or
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 15 QoS Setup Total 4 prioritized queues are provided for Ethernet packets, denoted as Queue0 (low
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 16 The following diagram denotes the path for tagged packets according to the above settings, S
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 17 Status and Statistics Show port LAN1/LAN2/HCNA Ethernet switch port link status and port sta
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 18 Device Noise in Master and EP ‘Noise Test’ measures each individual device HCNA interface noise
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 19 This diagnosis runs the downstream test from HP-51M toward EP. Also the result of ‘Rx Diagnos
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 20 Administrator For each account, 3 level of privilege is provided: Superuser, Read, and ReadWrit
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 21 For each programmed filter set, you can further specify if the protocol Telnet/Http/Snmp/Ping
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 22 Specify that if the built-in Telnet server, Web server, and Snmp agent is enabled or not and a
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 23 For example, To access your listed SNTP server by its domain name instead of IP address, the ‘
Dynamix HP-51M User Manual EN-V1.00 TTA B L E O F A B L E O F CCO N T E N T SO N T E N T S INTRODUCTIONINTRODUCTION ___________________
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 24 Activate Firmware To do the real upgrade for ‘Bootcode’ or ‘System Firmware’, make the previous
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 25 In the example, the onboard Master (denoted ‘Local’) device driver version is ’2.7.5-2’. The tw
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 26 Click ‘Browse’ button to locate where the new system firmware resides at your PC, then click
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 27 You may activate the new system firmware right away, or wait for the proper scheduled time in
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 28 If you don’t upload ‘System Firmware’ first, the ‘Upload Area’ is blank, Activate the New S
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 29 New system firmware version ’3.06’ shown on the ‘Information’ window, HCNA Driver Upload the
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 30 Also shown on ‘EP Management’ window (‘Upload Area’), Upgrade the New HCNA Driver Designate
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 31 Click ‘Upgrade’ button to proceed, Then ‘Upgrade’ button again to confirm, Upgrade EP one by
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 32 Master/EP runs the New HCNA Driver The ‘EP Management’ window that queries the properties fro
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 33
Allowed Source _______________________________________________________________________ 20!Telnet/Http/Snmp Setup ____________________________________
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 34 Use Telnet Any popular Telnet client could use to configure the bridge remotely. For example, r
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 35 Note that Telnet connection will be terminated automatically if the telnet client doesn’t inp
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 36 dir Show detail file information resides in flash ROM. Include ‘Working Area’ and ‘Upload Area
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 37 hpnareboot Reset Master HCNA device’ ipconfig [-a <ip> -m <mask> -g <default g
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 38 snmptrapserver [-s <set> [-c <act/deact>] [-p <port>] [-a <ip>] [-m <
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 39 [-c <lan1/lan2/off/del>] addresses can be setup, refer Static MAC <mac>: max 8 e
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 40 Use SNMP The SNMP Agent resides in HP-51M will handle requests from remote SNMP Manager. The HP
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 41 4 AADVANCED DVANCED FFEATURESEATURES This chapter describes the advanced features offered by y
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 42 A SSPECIPECIFICATIONSFICATIONS N E T W O R K I N T E R F A C E HomePNA3.1 over Coax(HCNA
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 43 Max Attenuation to Endpoint: 50dB (-176dBm/Hz Noise Floor) C O N N E C T O R S Ethernet
Dynamix HP-51M User Manual EN-V1.00 swqosrate____________________________________________________________________________ 38!swqostc __________
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 1 1 IINTRODUCTIONNTRODUCTION This chapter describes the features of your HomePNA3.1 over Coax to
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 2 2 IINSTALLATIONNSTALLATION This chapter describes the installation procedure for your bridge.
DYNAMIX HP-51M Coax MDU Master Bridge User’s Guide 3 Connecting the Cables To establish a new coax networking system by HP-51M, reroute the CATV/Ante
Kommentare zu diesen Handbüchern